Honeywell TR75 Thermostat User Manual

Home

Zio /Zio Plus LCD Wall Modules

TR70, TR71, TR75 WITH Sylk Bus

SPECIFICATION DATA

•

Programmable for: Home screen options, tenant

access, contractor access, optional password

protection to contractor mode, access to controller

parameters, setpoint, override, fan, and other

parameters.

•

Ability to access and adjust most parameters in the

programmable controller.

•

TR75 can access and adjust the controller schedule.

Ability to balance the VAV system from the wall

module.

•

Home screen can display one to three of any of the

following parameters: Temperature Setpoint, Room

Temperature, Room Humidity, Outdoor Humidity,

Outdoor Temperature, and Time, or one of virtually any

parameter in the controller.

•

Network bus jack.

Simple 2-wire terminal connection to the

programmable controller (includes power) and an

optional 2-wire terminal connection for the network. All

connections are polarity insensitive.

GENERAL

The TR70 Series Zio (TR70/TR70-H, TR71/TR71-H) and Zio

Plus (TR75/TR75-H) are 2-wire, non-polarity sensitive, Sylk

bus communicating wall modules for use with Spyder^®and

ComfortPoint™ programmable controllers.

•

Permanent retention of user configuration, including

setpoints after a power outage.

Table 1. TR70 Series Features.

All models have a space-temperature sensor, network bus

jack, and an LCD panel with three softkeys and two Up/Down

adjustment keys. The TR7-H, TR71-H and TR75-H models

include an onboard humidity sensor.

Zio

Zio Plus

TR75

Features

TR70 TR71

Scheduling

4.9K

Parameter Memory (bytes)

Up to four Zios on Sylk

Enumerated Values

NOTE: Refer to the Zio/Zio Plus LCD Wall Modules Oper-

ating Guide (form 63-2719) for information about

customizing the wall module configuration in the

WEBs-AX Workbench, such as modifying the

default Home screens or creating your own appli-

cation.

Setpoint Limits as NVs – linking

now possible

System and Fan command as NVs

Password protection

FEATURES

The TR70 Series wall modules include:

Firmware version/model visible on

display

•

Ability to control tenant access to controller

parameters via password protection.

0.5 and 5 value increments

•

Ability to assign labels for enumerated values.

"-" and "/" characters in parameter

names

Customized parameter access, by using the Honeywell

WEBs-AX Workbench tool.

* Support for up to four TR71 and/or TR75s per Spyder, and if

a TR70 is present, a maximum of three Zios (any combina-

tion of models) are allowed.

•

Ability to link setpoint limits to a network variable.

3-1322-02

ZIO /ZIO PLUS LCD WALL MODULES

SPECIFICATIONS

NET-1

NET-2

S-BUS

(

optional)

(optional)

Compatibility: Full feature set, including scheduling and

password protection requires the latest Spyder firmware

SLOTS FOR SUBBASE

LOCKING TABS (X4)

HONEYWELL

TR70-H

YY WK

PATENT PENDING

(field upgradeable with Spyder Flash Tool), Spyder Tool

GOLDEN VALLEY,MN

ASSEMBLED IN MEXICO

50028668-XXX

version greater than 5.18, and WEBs-AX Workbench ver-

sion 3.4.57 or greater.

WALL MODULE BUS

ADDRESS DIAL

(DEFAULT SETTING = 1)

Construction: Two-piece construction, cover and internally

wired subbase. Field wiring, 18 to 24 AWG (0.82 to 0.20

sq. mm), connects to a terminal block in the subbase.

7 6

S-BUS PROGRAMMABLE

Mounting Options: The LCD wall modules can be mounted

on a standard two by four inch junction box or on a 60 mm

diameter junction box. The modules may be mounted up to

CONTROLLER CONNECTION

NETWORK BUS

CONNECTION

200 ft. (61 m) from the programmable controller. Twisted

pair wiring is recommended for distances longer than 100

ft. (30.5 m).

Dimensions (H/W/D): See Fig. 2 on page 2.

EACH OF THE TWO WIRE CONNECTIONS FOR THE S-BUS AND NETWORK

BUS TERMINALS ARE POLARITY INSENSITIVE.

M27349

Environmental Ratings:

Operating Temperature: 30°F to 110°F (-1°C to 43°C)

Shipping Temperature: -40°F to 150°F (-40°C to 65.5°C)

Relative Humidity: 5% to 95% non-condensing

Fig. 1. LCD wall module components (rear view).

NOTE: 18 Vdc power for the LCD wall modules is sup-

plied from the programmable controller.

Temperature Setpoint Range: Default range is 55°F to 85°F

(10°C to 35°C); configurable for other ranges.

Module Dimensions

Temperature Sensor Accuracy: ±0.36°F at 77°F (±0.2°C at

5°C)

3 5/16 (84)

Humidity Sensor Accuracy (TR71-H/TR75-H only): ±5%

RH from 20% to 80% RH

Power: 18 Vdc power is supplied to the wall module from the

2-wire S-BUS connection to the programmable

controller.

Accessories: 50007298-001 (pack of 12) medium, cover

plate; 6-7/8 x 5 in. (175 x 127 mm).

4 5/8

(

117)

Approvals: CE; UL94-HB plastic enclosure; FCC Part 15,

Class B

Terminal Wiring Location

Fig. 1 illustrates the location of the terminal block and other

features on the TR70 Series wall modules.

5/16

24)

(

M27347

Fig. 2. Wall module dimensions in inches (mm).

Communications

The wall modules use a sensor bus (S-BUS) for

communications with the programmable controller.

For network communication, the building’s LON or BACnet®

network wires connect to the two terminals (NET-1 and NET-

). See Fig. 1. A network bus port is accessible at the bottom

of the wall module by removing the jack plug.

The network bus and S-BUS terminals (see Fig. 1) are

insensitive to polarity, minimizing installation errors due to

mis-wiring. The recommended wire size for the network bus

63-1322—02

ZIO /ZIO PLUS LCD WALL MODULES

and S-BUS is 18-24 AWG (0.82 to 0.20 sq mm) depending on

application, plenum or non-plenum rated, unshielded, twisted

pair, solid conductor wire.

LCD Display

The LCD display may be customized for tenant and contractor

users. The following are a few samples of the various Home

screens that are configurable for the LCD Wall Modules. Not

all possible Home screens are illustrated here. There are

many other configurable Home screens.

NOTES:

Home screens can display one to three of any of

the following parameters: Temperature Setpoint,

Room Temperature, Room Humidity, Outdoor

Humidity, Outdoor Temperature, and Time, or one

of virtually any parameter in the controller.

M27377

Fig. 5. Sample Tenant Home screen with

Setpoint display only.

Refer to the Zio/Zio Plus LCD Wall Modules Oper-

ating Guide (form 63-2719) for information about

customizing the wall module configuration in the

WEBs-AX Workbench, such as modifying the

default Home screens or creating your own appli-

cation.

Sample Tenant LCD Displays

The Fan and Occupied settings are optional for Home screen

setup. If there are no parameters configured for Tenant

access, the “View More” softkey does not display on the

Tenant Home screen.

M27356

Fig. 6. Sample Tenant “View More” display showing

CO sensor value from controller.

NOTE: Any configured parameter may be displayed.

Sample Contractor LCD Displays

The Contactor mode allows advanced options using the

softkeys. Contractor mode also allows for customizing the

Tenant view, including setting the tenant’s Home screen and

“View More” access.

M27354

Fig. 3. Sample Tenant Home screen with System Status,

Setpoint, Outside Temperature, and

Room Temperature (predominant).

M27357

Fig. 7. Sample Contractor Home screen display with

System Status, Setpoint, Outside Temperature,

and Room Temperature (predominant).

CONTACTOR HOME SCREEN SOFTKEYS

The three softkeys on the Contractor Home screen (Fig. 7)

provide the following:

SET HOME SCREEN - allows the contractor to choose

among multiple Home screen options for the tenant.

M27379

Fig. 4. Sample Tenant Home screen with Room

Temperature and Time (predominant).

63-1322—02

ZIO /ZIO PLUS LCD WALL MODULES

SET VIEW MORE - allows the contractor to give additional

parameter access (view only or adjustable) to the tenant.

TYPICAL SPECIFICATION

The wall module shall have an LCD display.

The wall module shall have a customizable home

screen:

PARAMETERS - allows the contractor to monitor and/or

adjust parameters in the programmable controller.

a. Shall have the option to show up to 3 parameter

values on a single display.

b. Shall have the option to show occupied status.

c. Shall have the option to show system status.

d. Shall have the option to show fan status.

e. Shall have the option to show up to three of the fol-

lowing parameters:

•

room temperature, setpoint, outside

temperature, room humidity, outside humidity,

time of day.

f. Shall have the option to show on the home screen

any single parameter in the controller, with a user

defined 8 letter name.

The wall module shall offer access to all parameters

necessary to balance a VAV system.

The wall module shall offer the ability to restrict access

to parameter information with keypad enabled lock out

and with optional 4 digit password protection (password

on TR71 and TR75 only).

M27358

Fig. 8. Sample Contractor parameter display showing

user-created discharge air parameter value.

The wall module shall retain user configuration including

setpoints after power outage.

The wall module shall use a two wire polarity insensitive

connection for all communication and power needs.

The wall module shall offer the ability to access and

adjust virtually all controller parameters.

The wall module shall offer the ability for the tenant to

adjust override time period within the limits set by the

contractor.

The wall module shall offer a communication jack for

remote access to the network.

M27359

10. The wall module shall offer a ± 5% on board humidity

sensor (TR70-H, TR71-H, and TR75-H only).

Fig. 9. Sample Contractor parameter display showing

sensor setpoint value (CO sensor from controller).

1. The wall module shall be configured through the Honey-

well WEBs-AX Workbench tool.

2. The wall module shall communicate with other devices

using the Sylk bus protocol.

3. The wall module shall be compatible with LON and

BACnet controllers.

4. The wall module shall offer the ability to view/edit the

controller's schedule (TR75 only).

5. The wall module shall have the ability to display enu-

merated values as text.

NOTE: Any configured parameter may be displayed.

6. The wall module shall have the ability to use the value of

a parameter as the upper or lower limit of another

parameter (TR75 only).

ComfortPoint™ is a trademark of Honeywell International Inc.

LONMARK® is a trademark of the LonMark Association.

BACnet® is a registered trademark of BACnet International.

Spyder® is a registered trademark of Honeywell International Inc.

Sylk® is a registered trademark of Honeywell International Inc.

Zio® is a registered trademark of Honeywell International Inc.

Automation and Control Solutions

Honeywell International Inc.

985 Douglas Drive North

U.S. Registered Trademark

3-1322—02 M.S. Rev. 12-11

Printed in United States

Golden Valley, MN 55422

customer.honeywell.com

Honeywell V8943CN Thermostat User Manual

White Rodgers 1F80 51 Thermostat User Manual

Bryant T6 PHP Thermostat User Manual

Honeywell EN2Z 0906GE51 R0708 Thermostat User Manual

Lennox XC2105 Thermostat User Manual

Aube TH113 A Thermostat User Manual

Carrier TCSNAC01 Thermostat User Manual

White Rodgers 1F85 0422 Thermostat User Manual

Honeywell T694B Thermostat User Manual

Lux Products WIN100 Series Thermostat User Manual